Search:

Type: Posts; User: ken mohr

Page 1 of 4 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    14
    Views
    1,506

    It was the fuel regulator. All is well now. Fires...

    It was the fuel regulator. All is well now. Fires on 1st compression stroke hot or cold. Thanks
  2. Replies
    14
    Views
    1,506

    I believe so. I will do it again

    I believe so. I will do it again
  3. Replies
    14
    Views
    1,506

    Changed coil, rotor cap, rotor, and ICM. Runs...

    Changed coil, rotor cap, rotor, and ICM. Runs great but still slow to start smell raw gas and some backfire. :dontknow:
  4. Replies
    14
    Views
    1,506

    No gas weep. Starting to think ignition. Had 2...

    No gas weep. Starting to think ignition. Had 2 strong back fires. Runs smooth cold then starts to slightly misfire as it warms.
  5. Replies
    14
    Views
    1,506

    Ok will do. Thanks

    Ok will do. Thanks
  6. Replies
    14
    Views
    1,506

    Now detecting miss at low RPMS and idle. Starting...

    Now detecting miss at low RPMS and idle. Starting hot detect raw gas odor.
  7. Replies
    4
    Views
    2,889

    Rack Replaced thanks

    Rack Replaced thanks
  8. Replies
    14
    Views
    1,506

    COLD Key on no reading ( may be Gauge) 41 when...

    COLD
    Key on no reading ( may be Gauge)
    41 when pump runs
    39 as soon as pump shuts off
    43 while cranking 1 2 seconds to start
    35 running
    34 light throttle
    Off
    15 minutes pressure 28
    Key on 40...
  9. Replies
    14
    Views
    1,506

    Will try this afternoon when I get home. Thanks ...

    Will try this afternoon when I get home. Thanks Ken
  10. Replies
    14
    Views
    1,506

    Sorry to take so long was a little under the...

    Sorry to take so long was a little under the weather. Is # 4 creating my problem?

    # 1--17.0 #2-- 17.1
    # 3--17.2 #4--15.3
    #5--17.1 #6--17.2
    #7--17.2 #8-- 17.4

    Thank You
    Ken
  11. Replies
    14
    Views
    1,506

    Thank you Will do

    Thank you Will do
  12. Replies
    14
    Views
    1,506

    hard start hot

    1989 corvette hard to start warm. Fires immediately cold. Is this an O2 sensor problem. Exhaust is very clean , almost not soot. If so what is best O2 to buy?
  13. Replies
    4
    Views
    2,889

    Thank You

    Thank You
  14. Replies
    4
    Views
    2,889

    89 Vette steering rack.

    Does anyone know where and if I can get a dust cover for 89 C4 steering rack. Came up with one missing. It goes at the end of pinion.
  15. Replies
    9
    Views
    3,669

    Welcome back. Never got bad info from you just...

    Welcome back. Never got bad info from you just for the record. 89 runs as good as the day it came off production line.
  16. Replies
    2
    Views
    1,898

    Thank You.

    Thank You.
  17. Replies
    2
    Views
    1,898

    Bore size for rebuild on master cylinder

    Can anyone tell me what the bore size is on an 89 coupe master cylinder?.. I am getting blow by to the rear reservoir. The numbers are - DHB- 39716. I believe that is a Dorman #

    Thank You
    Ken
  18. Replies
    0
    Views
    6,749

    clunk in transmission

    2006 Impala 3.9 engine. When accelerating from a stop I'm getting a clunk sometimes hard (almost feels like some bumped you from behind. It doesn't always do it. 80% of the time it acts just fine. I...
  19. Replies
    6
    Views
    4,344

    Very Nice :hello:

    Very Nice :hello:
  20. Replies
    0
    Views
    1,331

    holliday wishes

    Merry Christmas and Happy New Year to all. :hug:
  21. Replies
    6
    Views
    3,215

    1106

    1106
  22. Replies
    4
    Views
    2,430

    Are you talking about heat shields or the exhaust...

    Are you talking about heat shields or the exhaust itself. Ceramic coated the heat shields and painted the header mamanifolds with black 2000* heat paint. Now thinking I should have used silver
  23. Replies
    6
    Views
    3,215

    I did refinish the wheel and it came out great.

    I did refinish the wheel and it came out great.
  24. Thread: low coolant

    by ken mohr
    Replies
    21
    Views
    6,046

    :beer: Thanks

    :beer: Thanks
  25. Thread: low coolant

    by ken mohr
    Replies
    21
    Views
    6,046

    Got it back last Tue. All is well, runs great...

    Got it back last Tue. All is well, runs great everything working as designed. Now I hate to put it away for the winter. :drool::drool::drool:
Results 1 to 25 of 91
Page 1 of 4 1 2 3 4