Search:

Type: Posts; User: ALMSGT

Page 1 of 2 1 2

Search: Search took 0.07 seconds.

  1. Replies
    0
    Views
    154

    Rear Axle Nut Torque

    I have a 2003 Z06. I plan to replace the rear hubs and would like to confirm the rear axle nut torque specification. The service manual lists it as 118 lbs.-ft.. I believe that there was a TSB...
  2. Thread: Z06 tire size

    by ALMSGT
    Replies
    2
    Views
    7,953

    I have a 2003 Z06 and have been trying to find...

    I have a 2003 Z06 and have been trying to find tires. I have Michelin Pilot Sport 2 tires on it now, 265/40 zr17 in the front and 295/35 zr18 in the rear on the original wheels. I can purchase...
  3. Thread: Balancing Pins

    by ALMSGT
    Replies
    6
    Views
    11,281

    The following is from page 6-45 of the 2003...

    The following is from page 6-45 of the 2003 Corvette service manual:
    NEW FLYWHEEL, CLUTCH, AND PRESSURE PLATE ASSEMBLY ONTO AN EXISTING ENGINE:
    Do not transfer or install balance weights.
    I...
  4. Thread: Balancing Pins

    by ALMSGT
    Replies
    6
    Views
    11,281

    Hi Paul: Where would I find a copy of that...

    Hi Paul:
    Where would I find a copy of that process? Would it be in the service manual? While replacing the clutch assembly would you recommend replacing the torque tube couplers, bearings and...
  5. Thread: Balancing Pins

    by ALMSGT
    Replies
    6
    Views
    11,281

    Thank you very much for your reply. I thought...

    Thank you very much for your reply. I thought that that should be a standard procedure but that not all technicians follow it. I will look for a good technician and specify this procedure.
  6. Thread: Balancing Pins

    by ALMSGT
    Replies
    6
    Views
    11,281

    Balancing Pins

    As I recall there are balancing pins in the flywheel and these pins should be removed from the old flywheel and placed in the same locations in the new flywheel when replacing the clutch assembly. ...
  7. Replies
    9
    Views
    16,614

    I have always appreciated the excellent advice...

    I have always appreciated the excellent advice that you have provided to me. I am delighted that you can once again help people maintain their Corvettes.
  8. It took a while to get to it but I completed this...

    It took a while to get to it but I completed this project. The Comp Cams 5462 valve spring compressor made compressing the valve springs really easy. I used a Snap-on 24 mm deep offset wrench to...
  9. Thank you very much for your advice, which I will...

    Thank you very much for your advice, which I will follow when I do the job.
  10. Thank you very much for your reply. On the ls6 I...

    Thank you very much for your reply.
    On the ls6 I have read that it is not possible for the valve to drop into the cylinder when the piston is at top dead center. That is why I plan to initially...
  11. Replacing Valve Springs and Valve Seals in a 2003 Z06

    I plan to replace the valve springs and valve seals in my 2003 Z06. I will be using a Comp Cams 5642 valve spring compressor to compress the springs. I have read the service manual, read several...
  12. Replies
    17
    Views
    18,124

    I sent the EBCM to Brandon Hite at ABSFixer.com...

    I sent the EBCM to Brandon Hite at ABSFixer.com in Missouri. He charged $150.00 for the basic EBCM repair and an additional $50.00 to install a surge protector. You are also responsible for the...
  13. Replies
    17
    Views
    18,124

    I removed the EBCM and sent it to a repair shop...

    I removed the EBCM and sent it to a repair shop in Missouri to have the faulty component replaced and a surge protector installed. I installed the repaired unit in my car and there are no codes.
    If...
  14. Replies
    17
    Views
    18,124

    I believe that the C1214 code is triggered by a...

    I believe that the C1214 code is triggered by a faulty EBCM.
  15. Replies
    17
    Views
    18,124

    I found an excellent article on how to perform...

    I found an excellent article on how to perform this job with photos included. Here is the link:
    http://www.rjsmith.com/ecbm-replacement.html
  16. Replies
    17
    Views
    18,124

    Thank you very much for your help, I really...

    Thank you very much for your help, I really appreciate it.
  17. Replies
    17
    Views
    18,124

    Service Traction Control and ABS Display

    My 2003 Z06 with 31,515 miles on it just started displaying the "service traction control, service ABS" warning. I have the following codes In the DIC:
    10-PCM P1431H
    28-TCS C1214H C...
  18. Replies
    0
    Views
    2,635

    2003 Z06 Spark Plug Wires

    I am going to change the spark plugs and wires in my 2003 Z06. I know that I need to order the AC Delco 41-110 plugs. Does anyone know the part number for the wire set? gmpartshouse.com lists part...
  19. Replies
    4
    Views
    4,871

    Thank you Froggy. And thank you for your YouTube...

    Thank you Froggy. And thank you for your YouTube videos, which I find very helpful.
  20. Replies
    4
    Views
    4,871

    Caliper Pin Lubrication

    I am going to change the pads and rotors on my C5 Z06. The service manual says to use a high temperature silicone lubricant for this job. Is there a specific GM approved lubricant for this...
  21. Replies
    5
    Views
    4,837

    I found a post from Paul that recommends a 78...

    I found a post from Paul that recommends a 78 series battery so I'll get a new battery. I don't understand why the system failed one time and now it works every time. Could something else be...
  22. Replies
    5
    Views
    4,837

    Can anyone confirm that the AC Delco 78-7 year...

    Can anyone confirm that the AC Delco 78-7 year battery is the appropriate battery for my Z06?
  23. Replies
    5
    Views
    4,837

    Electrical Problem Again

    I reported this problem recently and experienced it again today. My 2003 Z06 did not respond to the remote key fob. I tried the other key fob and that did not work either. I unlocked the driver...
  24. Replies
    2
    Views
    5,462

    Battery Charging Question

    I have a 2003 Z06 that is not driven regularly. When I charge the battery I always disconnect both cables as I don't want to damage any sensitive electrical components. I have been told that it is...
  25. Replies
    10
    Views
    9,744

    I checked the battery, which is an Odyssey AGM,...

    I checked the battery, which is an Odyssey AGM, with a model B7 Solar battery manager device. The voltage was only 11.9 volts. I charged it to 12.7 volts and 757 CCA. It's okay now. Again, thank...
Results 1 to 25 of 32
Page 1 of 2 1 2