Search:

Type: Posts; User: ken mohr

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Injector ohms

    by ken mohr
    Replies
    1
    Views
    694

    Got it thanks.

    Got it thanks.
  2. Thread: Injector ohms

    by ken mohr
    Replies
    1
    Views
    694

    Injector ohms

    I have 7 injectors reading 16.2 ohms and one at 14.6, is this too far out of range? Also a loud clacking randomly. Is this possibly injector sticking? Sounds like in front of engine.

    Thank for...
  3. Thread: Quiet Tires

    by ken mohr
    Replies
    4
    Views
    6,512

    Put Michelin P4s on last summer. Very pleased so...

    Put Michelin P4s on last summer. Very pleased so far. American made..
  4. Looks good.

    Looks good.
  5. Replies
    1
    Views
    8,178

    Nice thank you

    Nice thank you
  6. Replies
    0
    Views
    6,691

    Average mileage gauge misbehaving

    Replaced the rotor cap and a harness in the distributor. The average mileage gauge is now incorrect. Shows 15MPG and jumps back to 0 then goes blank. This was and is before I had the cluster redone (...
  7. Replies
    2
    Views
    7,655

    Thank You for trying. Have a safe thanksgiving. ...

    Thank You for trying. Have a safe thanksgiving.

    Ken
  8. Replies
    2
    Views
    7,655

    Rack andd pinion

    Can anyone tell me what year this rack was from. Not sure of S/N 3 stamped on housing. 26008290, 011810H09, 69198. Also 2 or 2.25 turn. Was remanufactured and stamped T48

    PS the dust cap is...
  9. Replies
    14
    Views
    15,053

    It was the fuel regulator. All is well now. Fires...

    It was the fuel regulator. All is well now. Fires on 1st compression stroke hot or cold. Thanks
  10. Replies
    14
    Views
    15,053

    I believe so. I will do it again

    I believe so. I will do it again
  11. Replies
    14
    Views
    15,053

    Changed coil, rotor cap, rotor, and ICM. Runs...

    Changed coil, rotor cap, rotor, and ICM. Runs great but still slow to start smell raw gas and some backfire. :dontknow:
  12. Replies
    14
    Views
    15,053

    No gas weep. Starting to think ignition. Had 2...

    No gas weep. Starting to think ignition. Had 2 strong back fires. Runs smooth cold then starts to slightly misfire as it warms.
  13. Replies
    14
    Views
    15,053

    Ok will do. Thanks

    Ok will do. Thanks
  14. Replies
    14
    Views
    15,053

    Now detecting miss at low RPMS and idle. Starting...

    Now detecting miss at low RPMS and idle. Starting hot detect raw gas odor.
  15. Replies
    4
    Views
    9,918

    Rack Replaced thanks

    Rack Replaced thanks
  16. Replies
    14
    Views
    15,053

    COLD Key on no reading ( may be Gauge) 41 when...

    COLD
    Key on no reading ( may be Gauge)
    41 when pump runs
    39 as soon as pump shuts off
    43 while cranking 1 2 seconds to start
    35 running
    34 light throttle
    Off
    15 minutes pressure 28
    Key on 40...
  17. Replies
    14
    Views
    15,053

    Will try this afternoon when I get home. Thanks ...

    Will try this afternoon when I get home. Thanks Ken
  18. Replies
    14
    Views
    15,053

    Sorry to take so long was a little under the...

    Sorry to take so long was a little under the weather. Is # 4 creating my problem?

    # 1--17.0 #2-- 17.1
    # 3--17.2 #4--15.3
    #5--17.1 #6--17.2
    #7--17.2 #8-- 17.4

    Thank You
    Ken
  19. Replies
    14
    Views
    15,053

    Thank you Will do

    Thank you Will do
  20. Replies
    14
    Views
    15,053

    hard start hot

    1989 corvette hard to start warm. Fires immediately cold. Is this an O2 sensor problem. Exhaust is very clean , almost not soot. If so what is best O2 to buy?
  21. Replies
    4
    Views
    9,918

    Thank You

    Thank You
  22. Replies
    4
    Views
    9,918

    89 Vette steering rack.

    Does anyone know where and if I can get a dust cover for 89 C4 steering rack. Came up with one missing. It goes at the end of pinion.
  23. Replies
    9
    Views
    22,185

    Welcome back. Never got bad info from you just...

    Welcome back. Never got bad info from you just for the record. 89 runs as good as the day it came off production line.
  24. Replies
    2
    Views
    14,676

    Thank You.

    Thank You.
  25. Replies
    2
    Views
    14,676

    Bore size for rebuild on master cylinder

    Can anyone tell me what the bore size is on an 89 coupe master cylinder?.. I am getting blow by to the rear reservoir. The numbers are - DHB- 39716. I believe that is a Dorman #

    Thank You
    Ken
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4